Side changes cause error? [Solved]

Commander_Cody771 · Post by **Commander_Cody771** » Mon Aug 11, 2008 6:44 pm

I am determined to find out the issue to this:

Hidden/Spoiler:

[code]Message Severity: 3

.\Source\LuaHelper.cpp(312)

CallProc failed: (none):0: attempt to perform arithmetic on a nil value

stack traceback:

	(none): in function `AddCommandPost'

	(none): in function `ScriptPostLoad'[/code]

I made a new map to see if that did it but it didn't help a thing! All I did was make very light side changes and it is complaining about the CP's. BTW this is a completely new map. Not the other one.

computergeek · Post by **computergeek** » Mon Aug 11, 2008 7:38 pm

In your lua you messed something up with setting up command posts in your lua
look for inconsistencies in the

Hidden/Spoiler:

--This defines the CPs.  These need to happen first

    cp1 = CommandPost:New{name = "cp1"}

    cp2 = CommandPost:New{name = "cp2"}

    cp3 = CommandPost:New{name = "cp3"}

    cp4 = CommandPost:New{name = "cp4"}

    --This sets up the actual objective.  This needs to happen after cp's are defined

    conquest = ObjectiveConquest:New{teamATT = ATT, teamDEF = DEF, 

                                     textATT = "game.modes.con", 

                                     textDEF = "game.modes.con2",

                                     multiplayerRules = true}

    --This adds the CPs to the objective.  This needs to happen after the objective is set up

    conquest:AddCommandPost(cp1)

    conquest:AddCommandPost(cp2)

    conquest:AddCommandPost(cp3)

    conquest:AddCommandPost(cp4)

part, that will help you

Commander_Cody771 · Post by **Commander_Cody771** » Tue Aug 12, 2008 9:24 am

That's just the point! I didn't even go to the folder to where the LUAs were. And al I did was make side changes.

obiboba3po · Post by **obiboba3po** » Tue Aug 12, 2008 9:45 am

well it tends to work that if one little thing is messed up with the side, everything else gets messed up. that happened to me just a few topics back. i messed up something stupid in an odf, and it was complaining about the sky which i didnt touch. so go back over what you edited and make sure it is 100% perfect. if you think something may be messed up, post it here just to make sure.

Commander_Cody771 · Post by **Commander_Cody771** » Tue Aug 12, 2008 12:05 pm

Well. When the class selection appears after loading, the CP's aren't there.

elfie · Post by **elfie** » Tue Aug 12, 2008 12:12 pm

Belive it or not that sounds like a side issue to me. Check your sides, units odf and side.req and such.

Post by **AceMastermind** » Tue Aug 12, 2008 12:15 pm

No need to post here what's messed up, just undo whatever changes you made and make sure the default map works first, then make a change and test after each change until you run into the problem again, then you'll know what's causing your problem.

Commander_Cody771 · Post by **Commander_Cody771** » Wed Aug 13, 2008 1:32 pm

Hmmmmmmm. I'm gonna try a manual clean.

Post by **Teancum** » Wed Aug 13, 2008 1:40 pm

Does a brand new map with no changes have this issue?

Commander_Cody771 · Post by **Commander_Cody771** » Wed Aug 13, 2008 1:48 pm

No it does not have the issue. I did a manual clean and it got rid of the problem but non of the side changes showed up =(

REivEN · Post by **REivEN** » Wed Aug 13, 2008 2:21 pm

did you add dc: in front of the side ?

Commander_Cody771 · Post by **Commander_Cody771** » Wed Aug 13, 2008 2:41 pm

OMG THAT WAS IT! Thank you so much REivEN!

Side changes cause error? [Solved]

Side changes cause error? [Solved]

Re: I know I have already posted a topic but...

Re: I know I have already posted a topic but...

Re: I know I have already posted a topic but...

Re: I know I have already posted a topic but...

Re: I know I have already posted a topic but...

Re: I know I have already posted a topic but...

Re: I know I have already posted a topic but...

Re: I know I have already posted a topic but...

Re: I know I have already posted a topic but...

Re: I know I have already posted a topic but...

Re: I know I have already posted a topic but...