XSI freezing on startup

GuitarMan · Post by **GuitarMan** » Thu Oct 19, 2006 6:42 pm

I downloaded XSI 4.2 ModTool and installed it. I start it up and it shows the small startup screen that is in the middle of the computer screen. So I waited a while for it to start up thinking that it was just loading. A half hour later its still "loading" so I figure its a freez. It cant even get intothe actuall program. And the only way to get it off my screen is to log off and then back onto my computer. I even redownloaded and reinstalled it....... 3 TIMES! Is there any solution? Cuz I would like to take a crack at modelling.

Vertical · Post by **Vertical** » Sun Nov 05, 2006 12:32 pm

Erm, dont know if this will help but sometimes spyware/virus protection software will stop a program installing properly, maybe you could disable it just for the installation.

Or u could spend lots of money and buy XSI and hope it works

Post by **AceMastermind** » Sun Nov 05, 2006 7:09 pm

Yeah, i had sort of that same problem when i first tried to install XSI, i had to disable my firewall temporarily when installing because XSI connects to the internet on it's own, my firewall was preventing this "unknown" program from access to the internet.
After installing, i re-enabled the firewall and started XSI and when prompted by my firewall program to "allow" access, i clicked "yes", and there was no more problem.

Delta_57_Dash · Post by **Delta_57_Dash** » Sun Nov 05, 2006 10:09 pm

AceMastermind wrote:Yeah, i had sort of that same problem when i first tried to install XSI, i had to disable my firewall temporarily when installing because XSI connects to the internet on it's own, my firewall was preventing this "unknown" program from access to the internet.
After installing, i re-enabled the firewall and started XSI and when prompted by my firewall program to "allow" access, i clicked "yes", and there was no more problem.

yeah... don't you just LOVE IT when firewalls block a program for 2 hours, then finally give you an option to allow it to work?

stupid norton....

PieDude797 · Post by **PieDude797** » Sun Nov 05, 2006 10:44 pm

I sent him a PM about this, and he said that norton isn't the problem. Odd, how so many people can have the same problem right? Because this happened to me before too.

GuitarMan · Post by **GuitarMan** » Mon Nov 06, 2006 7:01 pm

I never said that Norton wasn't the problem. I said that it might NOT be the problem, cuz whever I run XSI the message never pops up, and that can mean three things. A-Norton isn't whats keeping XSI from running and the problem is something else, B-The Norton message is bieng a jack@$$ and it is taking forever to load (like it usually does), or 3-My computer has a mind of its own and its goal in life is to make me as mad as possible. I like the idea you have Ace, and I will try that.

Murdocr · Post by **Murdocr** » Tue Nov 07, 2006 1:38 pm

As an ex-norton user, i would place my bet on B. It takes forever to load anything. Try this; when you install XSI, go into norton and click on firewall. Then in the panel on the right side, click settings, or options or similar. Then there should be something on the screen that pops up called "exceptions". click add, then prowse to the .exe for xsi. This may not be exact, as it is a long time since i saw norton (thankfully) and you may have a different version to what i had. Hope this helps.

GuitarMan · Post by **GuitarMan** » Tue Nov 07, 2006 2:01 pm

I tried what you said Murdocr, and it still didnt work. Im starting to lose hope.

XSI freezing on startup

XSI freezing on startup

I had to disable my firewall